Nano Ceramic Coating for Car PPF Protection
PPFGuard is a flexible nano-coating product that increases the performance of paint protection films, protects the applied surface against various factors and extends the life of the surface. It is applied in 2 layers and the waiting time between coats is very short.
PPFGuard gives hydrophobic, UV resistance and easy-toclean properties to film-coated surface without spoiling the physical properties of glossy, matte, and satin surfaces. It prevents the color fading caused by sun rays and does not cause any change in the structure of films with self-healing feature.
Why PPF Guard?
- Ensures UV and chemical resistance for paint protection films.
- Up to 18-months of durability.
- Super finish with high hydrophobicity.
- No blocking self-healing effect of PPF.
- Recommended for professional detailers.
Application Surfaces
Nasiol PPFGuard is applicable to paint protection films (PPF) including matt & transparent polyurethane (PU), high quality PVC films, vinyls. Do not apply product on finishes including low quality PPF, PPF w/ bubbles, absorbent surfaces, temporary road films, interior window tints, any film without resistance to solvents.
Application
- For best results, ensure that the environment where the application will take place is as close as possible to the recommended levels of temperature and humidity (23°C and 50% relative humidity)
- Apply in a shaded area
- Only apply to surfaces that are not too cold or warm
- Wash your vehicle thoroughly and gently. If necessary, should the PPF surface is suitable, polishing treatments can be applied using silicone-free products.
- Dry the vehicle thoroughly to prevent water drops on the surface during application.
- Eliminate any dust and dirt on the surface before application using Nasiol Clean. Ensure that the surface has thoroughly dried.
- Partition the application area visually or with masking tape. Do not work on a partition larger than 1 m² at a time.
- Overlapping edges of partitions do not cause issues during application.
- Shake the product gently before use. Carefully remove the cap. Place the small suede cloth on the block applicator, and apply the necessary amount of product (depending on the size of the application area) onto the cloth. Recap the bottle in order to prevent air contact. Using the suede cloth, spread the product throughout the surface in horizontal and vertical movements.
- Using the enclosed microfiber cloth, carefully wipe any excess product off the surface within 30 – 60 seconds. Avoid causing swirls during this step. You can use a lighting system to ensure there is no product residue left on the surface. Following the application of the first layer, wait for 60 minutes, then repeat the steps for the second layer.
- Throughout the curing time, keep the coated surface away from direct sunlight, excessive dust, water, and other contaminants. For the first 48 hours, do not wash the surface with shampoo or detergents. The vehicle can be taken outdoors 24 hours after the application.
PPFGuard Specifications
| Volume | 50mL |
| Application surface type | Paint Protection Films (PPF) |
| Durability | 1 year / 50 washes: Normal conditions -20°C to +35°C, pH<12 detergent 6 months / 25 washes: Heavy conditions -40°C to +40°C, pH>12 detergent |
| Temperature durability | 275°C |
| Chemical resistance | 12>pH>1 |
| Consumption | 2-3 ml/m2 |
| Scratch resistance | |
| Water repellency | |
| Oil repellency | |
| Hologram reducing | |
| UV resistance | |
| Shelf life | 2 years when unopened 1 week after opening |
| Storage conditions | -3°C to +30°C |
| Curing period | 24h pre, 48 h totally |
UV Protection
High Chemical Resistance
High Hydrophobic
Easy Clean
FAQ
Nasiol nano ceramic coatings extend the life of car’s paintwork or paint protection films (PPF), provide protection against scratches and remove the most stubborn stains such as bird poop etching from the car easily thanks to its water and oil repellent characteristic. Besides, they preserve your car’s body against adverse effects of sunlight, acid rains and chemicals.
Nasiol PPFGuard is a protection product which is applied onto paint protection films (PPF). Also known as nano ceramic coating, this product makes the surface resistant against scratches and remove tenacious stains such as bird poop easily as it is water and oil repellent. By providing UV protection, it prevents PPFs from fading in course of time. It protects your vehicle for 1.5 years, making it appear just like the first day.
Nasiol PPFGuard is applied to the surfaces of Paint Protection Film (PPF): Polyurethane (PU) – Matt and Transparent Film, High Quality PVC Film and Vinyl Film.
It provides resistance up to 1.5 years.
Nasiol PPFGuard is applied in two coats. Approximate consumption for two coats is given below by class of the passenger cars:
Small Car: 20-30 mL (classes A-B)
Standard Car: 30-40 mL (classes C-D)
Big Car: 40-50 mL (classes E-SUV)
To get the best performance out of the product, make sure the temperature and relative humidity values (23°C and 50 RH) of the application surface are close as possible to the recommended conditions. Avoid direct sunlight during application and work on cool surfaces only. Wash your car thoroughly. If PPF surface allows, you may, if required, perform polishing by using silicon-free products. Dry the car thoroughly to prevent water drops on the surface during application. Remove dust and dirt on the surface with Nasiol Clean prior to application. Make sure the surface is completely dry. Isolate the application area visually or with masking tape. Do not work on an area larger than 1m2 at a time. Shake the bottle gently before use. Open the lid carefully. Place the suede cloth on the application apparatus and pour appropriate amount of product (2-3 mL/1m2) on the cloth. Close the bottle again to prevent contact with air during application. Spread the product by using the suede cloth with horizontal and vertical movements. Wipe off the excess product on the surface carefully within 30-60 seconds by using the microfiber that comes with the product and perform the polishing with circular movements by using the same cloth. You may use extra lighting system to make sure there is not product remnants left on the surface. Wait for 60 minutes after the application of the first coat and then repeat the same steps for the second coat. Keep the coated surface away from direct sunlight, dust, water and any dirt throughout the curing process. Do not wash the surface with shampoo or detergent in the first 48 hours. You may take out the car 24 hours after the application.
Before application, make sure the vehicle is clean and dry. Perform the application in a shady place.
In case of newly painted surfaces, the product should not be used within 3 months after the painting. The reason is that the product has much better performance to adhere to the completely dry paint. When the paint is not dry completely, the surface loses its full resolute (stable) character for adhesion of our coating products.
Water and oil repellence
Protection against capillary scratches
Protection against UV and discolouring
Resistance to chemicals
Protection against exterior effects
Easy to clean
When applied wrongly without giving due attention to the application instructions, the product can be removed from the surface only by polishing or sanding process.
Our prices vary depending on retail and wholesale. You may contact with us at our e-mail address of phone numbers to get information about our retail and wholesale prices. And you may also visit our online store at ekspermarket.com or online shopping websites for information about retail price.
We have toxicity certificates and MSDS documents evidencing that our products are not harmful to human health and environment. You may contact with our sales team and review these documents.
It is recommended to have it performed by professionals. But you also may apply it by reading the instructions on application.
Nasiol PPFGuard is applied in two coats. Wait for 60 minutes after completion of the first coat and then apply the second coat.
If you did not use the product completely after its bottle is opened, you may store it for 1 month by making sure it is tightly closed. If the bottle is not opened at all, it may be stored for 2 years under appropriate storage conditions.
Unlike the other products, Nasiol PPFGuard is applied on the paint protection films (PPF). While Nasiol PPFGuard provides durability up to 1.5 years, Nasiol NL272 up to 5 years, Nasiol ZR53 up to 3 years, Nasiol XR03 up to 1.5 years, Nasiol NeoCoatX up to 6months (one coat). Resistance of the products against scratch and environmental factors are different from each other.
Nasiol has not an official application centre yet. As we only supply the product and the application method of the product is essential for getting the desired durability and effect, such warranty or certificate can be given by an organization that applies it.
You may take advantage of our box-free trademark offer for Nasiol PPFGuard and you may make selections from the catalogue we have to this end and thus create your own trademark.
Nasiol PPFGuard is appropriate for Paint Protection Film (PPF): Polyurethane (PU) – Matt and Transparent Film, High Quality PVC Film, Vinyl Film surfaces. It should not be applied to other surfaces.
Our Nano coatings contain nano-sized silicon dioxide and other chemical particles.
You are recommended to use gloves during application. If it contacts with your skin inadvertently, wash it immediately with plenty of water and soap. After it contacts with your skin, remove all your contaminated clothes immediately and wash them immediately with plenty of water. If sensitization persists on, consult medical aid.
Most of the Nasiol products are solvent-based and they, therefore, smell in liquid form. They are odour-free when and cured on the surface.
Nasiol PPFGuard provides protection against little scratches and dents caused by key and pebble etc.
Box contains Nasiol PPFGuard Glass Bottle (50 mL), Nasiol Application Apparatus, Nasiol Suede Cloth x5, Nasiol Microfiber Cloth (Light Gray) x1, Nasiol Gloves (Black), Nasiol Glass Sticker, User Instructions (as printed on the box).
There are 10 products in one cartoon of Nasiol PPFGuard.
Yes. You may take advantage of our box-free trademark offer for Nasiol PPFGuard; you may make selections from the catalogue we have to this end and thus create your own trademark.
You should allow it for 48 hours for get full performance out of the product.
